Find great deals for Makita Cordless Drill Model 6010SD Charger Instruction Manual Late 1980s. Shop with confidence on eBay! INSTRUCTION MANUAL IMPORTANT: Read Before Using. Cordless Hammer Driver Drill DHP343 DHP453. Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium. • Cordless Driver DrillEquipped with Electric BrakeMODEL 6217DMODEL 6237DMODEL 6317DMODEL 6337DMODEL 6347DI N S T R U C T I O NM A N U A LWARNING:For your personal safety, READ and UNDERSTAND before using.SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.w w w. M a k i t a t o o l s. • SPECIFICATIONSModel6217DSteel6237D6317D10 mm (3/8”)6337D6347D13 mm (1/2”)WoodNo loadspeed (RPM)Wood screw6 x 75 mm(1/4” x 3”)6 x 75 mm(1/4” x 3”)6 x 75 mm(1/4” x 3”)6 x 75 mm(1/4” x 3”)10 x 89 mm(3/8” x 3-1/2”)MachinescrewCapacities25.4 mm (1”)32 mm(1-1/4”)13 mm(1/2”)13 mm(1/2”)13 mm(1/2”)13 mm(1/2”)13 mm(1/2”)High32 mm(1-1/4”)38 mm(1-1/2”)0 - 1,300/min. 0 - 1,300/min. 0 - 1,300/min. 0 - 1,300/min. 0 - 1,300/min.0 - 400/min. • GENERAL SAFETY RULESUSA003-1(FOR All BATTERY OPERATED TOOLS)WARNING:Read and understand all instructions. ![]() ![]() Failure to follow allinstructions listed below, may result in electric shock, fire and/orserious personal injury.SAVE THESE INSTRUCTIONSWork Area1. Keep your work area clean and well lit.Cluttered benches and dark areas invite accidents.2. Do not operate power tools in explosiveatmospheres, such as in the presence offlammable liquids, gases, or dust. • Tool Use and Care12. Use clamps or other practical way tosecure and support the workpiece to astable platform. Holding the work by hand oragainst your body is unstable and may leadto loss of control.13. Do not force tool. Use the correct tool foryour application. The correct tool will do thejob better and safer at the rate for which it isdesigned.14. Do not use tool if switch does not turn iton or off. A tool that cannot be controlledwith the switch is dangerous and must berepaired.15. Be sure no one is below when using thetool in high locations.5. Hold the tool firmly.6. Keep hands away from rotating parts.7. Do not leave the tool running. Operate thetool only when hand-held.8. Do not touch the drill bit or the workpieceimmediately after operation; they may beextremely hot and could burn your skin.9. Some material contains chemicals whichmay be toxic. Take caution to preventworking dust inhalation and skin contact.Follow material supplier safety data. Use of an attachment not recommendedor sold by the battery charger manufacturer may result in a risk of fire, electricshock, or injury to persons.6. To reduce risk of damage to electric plugand cord, pull by plug rather than cordwhen disconnecting charger.7. Make sure cord is located so that it willnot be stepped on, tripped over, or otherwise subjected to damage or stress.improper extension cord could result in arisk of fire and electric shock. If extensioncord must be used, make sure:a. Do not allow anything to cover or clog thecharger vents.4. Always cover the battery terminals withthe battery cover when the battery cartridge is not used.5. Do not short the battery cartridge:(1) Do not touch the terminals with anyconductive material.(2) Avoid storing battery cartridge in acontainer with other metal objectssuch as nails, coins, etc.(3) Do not expose battery cartridge towater or rain. • FUNCTIONALDESCRIPTION•001892CAUTION:Always be sure that the tool is switched off and thebattery cartridge is removed before adjusting orchecking function on the tool.Installing or removing battery cartridge•To remove the battery cartridge, withdraw it from the toolwhile pressing the buttons on both sides of the cartridge.•To insert the battery cartridge, align the tongue on thebattery cartridge with the groove in the housing and slipit into place. • NOTE:•The battery charger is for charging Makita batterycartridge. Never use it for other purposes or for othermanufacturer’s batteries.•When you charge a new battery cartridge or a batterycartridge which has not been used for a long period oftime, it may not accept a full charge. This is a normalcondition and does not indicate a problem. You canrecharge the battery cartridge fully after discharging itcompletely and recharging a couple of times. • 001894Switch action•1CAUTION:Before inserting the battery cartridge into the tool,always check to see that the switch trigger actuatesproperly and returns to the “OFF” position whenreleased.To start the tool, simply pull the switch trigger. Tool speed isincreased by increasing pressure on the switch trigger.Release the switch trigger to stop.1. Switch triggerElectric brakeThis tool is equipped with an electric brake. • •001897Selecting action modeThis tool has an action mode change lever. For drilling,depress the lock button and then slide the action modechange lever to the left (symbol). For screwing, slide theaction mode change lever to the right (symbol) until it islocked.12If it is hard to turn the lever, first turn the chuck slightly ineither direction and then turn the lever again.1. Lock button2.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |